Quantcast Appendix C: REPAIR PARTS AND SPECIAL TOOLS LIST - TM-55-1730-208-130041

 

Click here to make tpub.com your Home Page

Page Title: Appendix C: REPAIR PARTS AND SPECIAL TOOLS LIST
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
MAINTENANCE ALLOCATION CHART FOR JACK, HYDRAULIC, TRIPOD, 10-TON
Up
TM-55-1730-208-13 Jack Hydraulic Part Number 50J25178 (TYPE B6) Manual
Next
Explanation of Columns. - TM-55-1730-208-130042
TM 55-1730-208-13
APPENDIX C
REPAIR PARTS AND SPECIAL TOOLS LIST
(Current as of 1 March 1971 )
Section I. INTRODUCTION
C-1. Scope.
Code
Explanation
This appendix lists repair parts and maintenance
supplies required for the performance of organizational
P2
Repair parts, special tools and test equipment
and direct support maintenance of the type B-6, 10-ton,
which are procured and stocked for insurance
jack, hydraulic, tripod.
purposes because the combat or military
essentiality of the end item dictates that a
minimum quantity be available in the supply
C-2. General.
system.
This basic issue items, repair parts, and special
tools listing is divided into the following sections:
P9
Assigned to items which are NSA design
controlled: unique repair parts, special tools,
a. Basic Issue Items-Section II. Not applicable.
test, measuring and diagnostic equipment,
b. Maintenance and Operating Supplies-Section III.
which are stocked and supplied by the Army
Not applicable.
COMSEC Logistic System and which are not
c. Prescribed Load Allowance (PLA) Section IV.
subject to the provisions of AR 380-41.
Not applicable.
d. Repair Parts Section V.  A list of repair parts
P10
Assigned to items which are NSA design
authorized for the performance of maintenance at the
controlled : special tools, test, measuring
organizational and direct support level in figure and item
and  diagnostic  equipment  for  COMSEC
number sequence.
support, which are accountable under the
Maintenance supplies (MS) are listed within the section
provisions of AR 380-41, and which are
in ascending Federal stock number sequence.
stocked and supplied by the Army COMSEC
e. Special Tools,  Test and Support Equipment
Logistic System.
Section VI. Not applicable.
f. Federal Stock Number and Reference Number
M
Repair parts, special tools and test equipment
Index Section VII. A list of Federal stock numbers in
which are not procured or stocked, as such, in
ascending numerical sequence, followed by a list of
the supply system but are to be manufactured
reference numbers appearing in all the listings, in
at indicated maintenance levels.
ascending alpha-numerical sequence. cross-referenced
to the illustration figure and item number.
A
Assemblies which are not procured or stocked
as such, but are made up of two or more
C-3. Explanation of Columns.
units. Such component units carry individual
The following provides an explanation of columns in
stock numbers and descriptions, are procured
the tabular lists in section V.
and stocked separately  and  can
be
assembled to form the required assembly at
a. Source, Maintenance and Recoverability (Codes
indicated maintenance categories.
(SMR).
(1) Source code indicates the selection status
X
Parts and assemblies that are not procured
and source for the listed item. Source codes are:
or stocked because the failure rate is normally
below that of the applicable end item of
Code
Explanation
component.
The failure of such part or
P
Repair parts, special tools and test equipment
assembly should result in retirement of the
supplied from the GSA/DSA, or Army
end item from the supply system.
supply system, and authorized for use at
indicated maintenance categories.
X1
Repair parts which are not procured or stocked.
The requirement for such items will be filled
by the next higher assembly or component.
C-1

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.